http://www.mg-rover-teile.de

Autor Thema: MG/Rover-spezifische Fehlercodes  (Gelesen 3696 mal)

Offline TamberlanE

  • Club Hessen
  • MG/Rover Forum Mitglied
  • ***
  • Beiträge: 568
  • Geschlecht: Männlich
  • MG ZS180 RT
    • MG/Rover-Club Hessen
MG/Rover-spezifische Fehlercodes
« am: 21. Februar 2013, 16:17:49 »
Hallo zusammen,

ich habe mal eine Rover-spezifische Fehlercodeliste zusammengestellt. Es muss noch verifiziert werden, für welche Modelle die gilt, ich vermute für alle (R)F und (R)T - Benziner.  :iroc:




P-Code  Beschreibung SAE J2012  Beschreibung MG/Rover ECM
P1000  PCM has been reset, no diagnostic results available  Permanent power supply interrupted  Bosch M5.2.1 (PetrolV8) 
P1117  Engine Coolant Temperature RadiatorOutlet Sensor Low Input 
P1118  Engine Coolant Temperature RadiatorOutlet Sensor High Input 
P1129  O2 Sensors Swapped Bank to Bank(Sensor 1)  Front HO2 Sensors transposed  Bosch M5.2.1 (PetrolV8) 
P1140  Upstream oxygen sensor 1 - malfunction  Siemens EMS 2000 
P1160  Upstream oxygen sensor 2 - malfunction  Siemens EMS 2000 
P1170  Downstream Fuel Trim Malfunction (Bank1)  Front HO2 Sensor aged - ATV adaption too lean / too rich LH bank  Bosch M5.2.1 (PetrolV8) 
P1171  System too Lean Bank A  Additive injector adaptive fuelling, lean limit exceeded LH bank 
P1172  System too Rich Bank A and Bank B  Additive injector adaptive fuelling, rich limit exceeded LH bank 
P1173  Downstream Fuel Trim Malfunction (Bank2)  Front HO2 Sensor aged - ATV adaption too lean / too rich RH bank  Bosch M5.2.1 (PetrolV8) 
P1174  System too Lean Bank B  Additive injector adaptive fuelling, lean limit exceeded RH bank 
P1175  System too Rich Bank B  Additive injector adaptive fuelling, rich limit exceeded RH bank 
P1776  Electronic Automatic Transmission (EAT) Torque interface error 
P1185  Upstream (pre-catalyst) oxygen sensorheater - electrical fault  MEMS3 
P1186  Upstream (pre-catalyst) oxygen sensorheater - electrical fault  MEMS3 
P1188  Fuelling Trim Adaption Bank A 
P1189  Fuelling Trim Adaption Bank B 
P1191  Downstream (post-catalyst) oxygen sensor heater - electrical fault  MEMS3 
P1192  Downstream (post-catalyst) oxygen sensor heater - electrical fault  MEMS3 
P1195  Pressure regulator valve malfunction  Bosch EDC15C (M47R diesel engine) 
P1230  Fuel Pump Relay Malfunction  Fuel pump relay open circuit  Siemens EMS 2000 
P1231  Fuel Pump Relay Circuit Low  Fuel pump relay short circuit to earth  Siemens EMS 2000 
P1232  Fuel Pump Relay Circuit High  Fuel pump relay short circuit to batteryvoltage  Siemens EMS 2000 
P1255  Low pressure fuel sensor malfunction  Bosch EDC15C (M47R diesel engine) 
P1300  Misfire Detected Sufficient to Cause Catalyst Damage  Catalyst damaging level of misfire on morethan one cylinder  Bosch M5.2.1 (Petrol V8) 
P1301  No description  Catalyst damaging level of misfire detectedon cylinder No.1  Bosch M5.2.1 (Petrol V8) 
P1302  No description  Catalyst damaging level of misfire detectedon cylinder No. 2  Bosch M5.2.1 (Petrol V8) 
P1303  No description  Catalyst damaging level of misfire detectedon cylinder No. 3  Bosch M5.2.1 (Petrol V8) 
P1304  No description  Catalyst damaging level of misfire detectedon cylinder No.4  Bosch M5.2.1 (Petrol V8) 
P1305  No description  Catalyst damaging level of misfire detectedon cylinder No.5  Bosch M5.2.1 (Petrol V8) 
P1306  No description  Catalyst damaging level of misfire detectedon cylinder No.6  Bosch M5.2.1 (Petrol V8) 
P1307  No description  Catalyst damaging level of misfire detectedon cylinder No.7  Bosch M5.2.1 (Petrol V8) 
P1308  No description  Catalyst damaging level of misfire detectedon cylinder No. 8  Bosch M5.2.1 (Petrol V8) 
P1316  Cylinder block - misfire causing increased emissions  MEMS3 
P1319  Cylinder banks misfire at low fuel level  Siemens EMS 2000 
P1320  CKP sensor - flywheel adaption for misfire detection, adaption limit  Siemens EMS 2000 
P1321  CKP sensor - flywheel adaption for misfire detection, tooth error  Siemens EMS 2000 
P1402  Downstream oxygen sensor - malfunction  Siemens EMS 2000 
P1412  Secondary Air Injection SystemMalfunction (Bank 1) 
P1413  Secondary Air Injection System Air Control Valve Always Open (Bank 1) 
P1414  Secondary Air Injection System Low Air Flow (Bank 1) 
P1415  Secondary Air Injection SystemMalfunction (Bank 2) 
P1416  Secondary Air Injection System Air Control Valve Always Open (Bank 2) 
P1417  Secondary Air Injection System Low Air Flow (Bank 2) 
P1450  Evaporative Emission Control SystemLeakage Pump Circuit Plausibility 
P1451  Evaporative Emission Control SystemLeakage Pump Circuit High 
P1452  Evaporative Emission Control SystemLeakage Pump Circuit Low Current 
P1453  Evaporative Emission Control SystemLeakage Pump Circuit High Current 
P1470  Varaible intake balance valve always open  Siemens EMS 2000 
P1471  Variable intake balance valve always closed  Siemens EMS 2000 
P1472  Variable intake butterfly (power) valves - always open  Siemens EMS 2000 
P1473  Variable intake butterfly (power) valves - always closed  Siemens EMS 2000 
P1474  Variable intake balance valve - electrical short to battery  Siemens EMS 2000 
P1475  Variable intake balance valve - electrical short to earth or open circuit  Siemens EMS 2000 
P1476  Variable intake butterfly (power) valves - electrical short to battery  Siemens EMS 2000 
P1477  Variable intake butterfly (power) valves - electrical short to earth or open circuit  Siemens EMS 2000 
P1506  Idle air control (IAC) valve stepper motor drive - circuit fault  MEMS3 
P1507  Idle air control (IAC) valve stepper motor drive - circuit fault  MEMS3 
P1508  Idle air control (IAC) valve stepper motor drive - circuit fault  MEMS3 
P1509  IACV Opening Coil Malfunction  Open circuit or short circuit to battery supply or earth - opening windings  Bosch M5.2.1 (PetrolV8) 
P1510  IACV - Opening Coil Circuit Malfunction 
P1513  IACV - opening Coil Circuit Low 
P1514  IACV Opening Coil Circuit High 
P1535  Air Conditioning Compressor RequestMalfunction  ATC requested when not in standby mode 
P1536  Air Conditioning Compressor RequestRange / Performance  ATC compressor clutch relay open circuit  Bosch M5.2.1 (PetrolV8) 
P1537  Air Conditioning Compressor Request LowInput  ATC compressor clutch relay short to earth  Siemens EMS 2000 
P1538  Air Conditioning Compressor Request HighInput  Air conditioning clutch relay - short tobattery voltage  Siemens EMS 2000 
P1550  IACV - Closing Coil Malfunction  Open circuit or short circuit to battery supply or earth - closing windings  Bosch M5.2.1 (PetrolV8) 
P1551  IACV - Closing Coil Circuit Malfunction 
P1552  IACV - Closing Coil Circuit Low 
P1553  IACV - Closing Coil Circuit High 
P1565  Cruise control (interface ECU) - short circuit to battery voltage  Siemens EMS 2000 
P1566  Cruise control (interface ECU) - short circuit to earth or open circuit  Siemens EMS 2000 
P1590  ABS Rough Road Signal Circuit Malfunction  Hardware is OK but the SLABS ECU is sending an error signal  Bosch M5.2.1 (PetrolV8) 
P1591  ABS Rough Road Signal Circuit Low  Signal from SLABS ECU shorted to ground or open circuit  Bosch M5.2.1 (PetrolV8) 
P1592  ABS Rough Road Signal Circuit High  Signal from SLABS ECU shorted to batteryvoltage  Bosch M5.2.1 (PetrolV8) 
P1610  - Main relay - short to battery voltage  Siemens EMS 2000 
P1611  - Main relay - short to earth or open circuit  Siemens EMS 2000 
P1640  - CAN Bus - CAN message failure  MEMS3 
P1641  - CAN Bus - bus failure  Siemens EMS 2000 
P1645  - ASC1 (message from ASR unit) - framemissing  Siemens EMS 2000 
P1646  - CAN Bus - automatic transmission message fault  Siemens EMS 2000 
P1647  - CAN Bus - message from instrument packfault  Siemens EMS 2000 
P1663  Throttle Angle / Torque Signal Circuit Malfunction  SLABS HDC link open circuit  Bosch M5.2.1 (PetrolV8) 
P1664  Throttle Angle / Torque Signal Circuit Low  SLABS HDC link short to ground  Bosch M5.2.1 (PetrolV8) 
P1665  Throttle Angle / Torque Signal Circuit High  SLABS HDC link short circuit to batteryvoltage  Bosch M5.2.1 (Petrol V8) 
P1666  Engine Anti-Theft Signal Circuit Malfunction  Alarm ECU - security code not received  Siemens EMS 2000 
P1667  Engine Anti-Theft Signal Circuit Low  Serial link short to earth  Bosch M5.2.1 (Petrol V8) 
P1668  Engine Anti-Theft Signal Circuit High  Serial link open circuit  Bosch M5.2.1 (Petrol V8) 
P1669  Engine Control Module Cooling Fan CircuitMalfunction 
P1670  Engine Control Module Cooling Fan CircuitLow 
P1671  Engine Control Module Cooling Fan CircuitHigh 
P1672  Engine Anti-Theft Signal Wrong CodeReceived  Alarm ECU - security code incorrect  Siemens EMS 2000 
P1673  Engine Anti-Theft Signal New EngineControl Module Not Configured  New ECM fitted  Bosch M5.2.1 (Petrol V8) 
P1674  Engine Anti-Theft Signal  No code ECM, valid code received  Bosch M5.2.1 (Petrol V8) 
P1675  Condensor Fan Circuit Malfunction 
P1700  Transfer Box Indicated Range - Performance  Low range signal implausible  Bosch M5.2.1 (Petrol V8) 
P1701  Transfer Box has signalled a fault condition to the Engine Control Module 
P1702  Transfer Box - Signal Line CommunicationFrame Error 
P1703  Transfer box link - signal line permanentlyat 12V or open circuit 
P1708  Transfer box link - signal line permanentlyat ground 
P1775  - CAN Bus - Automatic gearbox GIU MIL request  MEMS3 
P1776  Transmission Control System Torque Interface Malfunction  EAT Torque interface error  Bosch M5.2.1 (Petrol V8) 
P1785  - Steptronic EM-CVT ratio control motor - drive over temperature  MEMS3 
P1787  - Steptronic EM-CVT ratio control motor - open circuit  MEMS3 
P1788  - Steptronic EM-CVT ratio control motor - ratio control motor over current  MEMS3 
P1810  - Steptronic EM-CVT PRNDM LED module - circuit fault  MEMS3 
P1815  - Steptronic EM-CVT Manual +/- switch - gear shift up signal fault  MEMS3 
P1816  - Steptronic EM-CVT Manual +/- switch - gear shift down signal fault  MEMS3 
P1830  - Steptronic EM-CVT PWM link from ECM toGIU - circuit fault  MEMS3 
P1831  - Steptronic EM-CVT PWM link from ECM toGIU - circuit fault  MEMS3 
P1836  - Steptronic EM-CVT serial link from GIU toECM - no serial data transmitted  MEMS3 
P1837  - PWM link from ECM to instrument pack - circuit fault  MEMS3 
P1838  - PWM link from ECM to instrument pack - circuit fault  MEMS3 
Nail here [ ] for a new monitor